| Other Information | Oscilloscope Bandwidth: bFluke 125:/b 40 MHzbFluke 124:/b 40 MHzbFluke 123:/b 20 MHz Dual input True RMS Meter: Vdc, Vac, Vac+Vdc, Ohms,Continuity , Diode-testCurrent, ?C, ?F, Capacitance, dBV, dBM, Crest Factor, Touch Hold and Zeroset TrendPlot Recording: Automatic vertical scaling and time compression.Display the actual, MIN, MAX and AVG reading. Cursors: bFluke 125/124:/b?T, 1/?T, V, ?V, rise- and fall time Real-time sample rate: 25 MS/s Equivalent sampling rate: up to 2.5 GS/s (125, 124) or 1.25 GS/s (123) Inputs and digitizers: 2 Timebase range: bFluke 125/124:/b 20 ns - 1 min/divbFluke 123:/b 10 ns - 1 min/div Input sensitivity: 5 mV - 500 V/div Trigger types: Connect-and-View?, Free Run, Single Shot, Edge, Video, External Trigger types: Connect-and-View, Free Run, Single Shot, Edge, Video, External Glitch capture: 40 ns Scope measurements: Automatic measurements: 26 (all instruments) On top, Fluke 125 has additional measurement functions for Power (W), VA, VAR and Power Factor (PF) for single phase and balanced-three-phase (delta) power systems. Harmonics mode: Fluke 125 has capbility to analyze the harmonics contents of power signals. See below for details Maximum record length: 512 min/max pts per input Memory: 512 min/max pts per input Memory: bFluke 125/124:/b 20 screens and setupsbFluke 123:/b 10 screens and setups Bus Health test:: Verifies the electrical parameters of industrial bus systems using automatic measurement and analysis functions. Next to that, an Eyepattern mode is provided for visual inspection of signal quality. Parameter classification:: Default values:? well within limits = ?good?? within certain percentage of the limit values = ?weak?? beyond limit values = ?bad?Limits values, as a default, are based on industry standard for the selected bus type or may be set by the user. Bus systems supported:: ? AS-i (EN50295, 166 kb/s);? CAN-bus (ISO-11898, up to 1 Mb/s);? Interbus S (EIA-485, 500 kb/s);? ControlNet (61158 type 2, 5Mb/s);? Modbus (EIA-232 up to 115 kb/s and EIA-485 up to 10 Mb/s);? Foundation Fieldbus H1 (61158 type 1, 31.25 kb/s);? Profibus DP (EIA-485 up to 10 Mb/s);? Profibus PA (61158 type 1, 31.25 kb/s);? Ethernet 10Base2 (coaxial);? Ethernet 10BaseT (UTP, 10 Mb/s);? RS-232 (EIA-232, up to 115 kb/s);? RS-485 (EIA-485, up to 10 Mb/s);? user defined single wire or balanced system. Modes:: Waveform Parameter analysis with automatic read-out and parameter? validation (good / weak / bad); test limits are based on industry standards or may be set by the user.? Eyepattern display mode. Measured parameters (where applicable):: ? baud rate,? risetime,? fall time,? high level,? low level,? bias voltage level,? signal amplitude,? distortion,? jitter. Eyepattern display mode:: Gives waveform display of bus signals with display persistence. Timebase and attenuator settings may be altered by the user. Measurement types:: ? Watt,? VA,? VAR,? Power Factor (PF) Power configuration:: Single phase or balanced three-phase (delta-configuration) mains supply Voltage measurement:: Channel A; using STL120, voltage probe or direct input Current measurement:: Channel B, using i400s (included) or other compatible current clamp Current Clamp or Shunt sensitivity:: 0.1 / 1 / 10 / 100 / 1000 mV/A, 10 mV/mA and 400 mV/A : Converts waveform information into a harmonics display (using FFT processing) which shows the relative amplitudes of the 1st up to the 33rd harmonic Harmonics Frequency range:: DC up to 33rd harmonic (for fundamental up to 60 Hz);DC up to 24th harmonic (for fundamental up to 400 Hz). Display: Bargraph showing 1st up to 33rd harmonic and DC; amplitude displayed in % relative to fundamental Measurements:: Relative amplitude of individual harmonics;THD in %r or %f. Operating Temperature: 0 ?C to 50 ?C Storage Temperature: -20 ?C to +60 ?C Operating Altitude: 3,000 m Electrical Safety: 600V CAT III (EN61010-1) | Oscilloscope Bandwidth: bFluke 125:/b 40 MHzbFluke 124:/b 40 MHzbFluke 123:/b 20 MHz Dual input True RMS Meter: Vdc, Vac, Vac+Vdc, Ohms,Continuity , Diode-testCurrent, ?C, ?F, Capacitance, dBV, dBM, Crest Factor, Touch Hold and Zeroset TrendPlot Recording: Automatic vertical scaling and time compression.Display the actual, MIN, MAX and AVG reading. Cursors: bFluke 125/124:/b?T, 1/?T, V, ?V, rise- and fall time Real-time sample rate: 25 MS/s Equivalent sampling rate: up to 2.5 GS/s (125, 124) or 1.25 GS/s (123) Inputs and digitizers: 2 Timebase range: bFluke 125/124:/b 20 ns - 1 min/divbFluke 123:/b 10 ns - 1 min/div Input sensitivity: 5 mV - 500 V/div Trigger types: Connect-and-View?, Free Run, Single Shot, Edge, Video, External Trigger types: Connect-and-View, Free Run, Single Shot, Edge, Video, External Glitch capture: 40 ns Scope measurements: Automatic measurements: 26 (all instruments) On top, Fluke 125 has additional measurement functions for Power (W), VA, VAR and Power Factor (PF) for single phase and balanced-three-phase (delta) power systems. Harmonics mode: Fluke 125 has capbility to analyze the harmonics contents of power signals. See below for details Maximum record length: 512 min/max pts per input Memory: 512 min/max pts per input Memory: bFluke 125/124:/b 20 screens and setupsbFluke 123:/b 10 screens and setups Bus Health test:: Verifies the electrical parameters of industrial bus systems using automatic measurement and analysis functions. Next to that, an Eyepattern mode is provided for visual inspection of signal quality. Parameter classification:: Default values:? well within limits = ?good?? within certain percentage of the limit values = ?weak?? beyond limit values = ?bad?Limits values, as a default, are based on industry standard for the selected bus type or may be set by the user. Bus systems supported:: ? AS-i (EN50295, 166 kb/s);? CAN-bus (ISO-11898, up to 1 Mb/s);? Interbus S (EIA-485, 500 kb/s);? ControlNet (61158 type 2, 5Mb/s);? Modbus (EIA-232 up to 115 kb/s and EIA-485 up to 10 Mb/s);? Foundation Fieldbus H1 (61158 type 1, 31.25 kb/s);? Profibus DP (EIA-485 up to 10 Mb/s);? Profibus PA (61158 type 1, 31.25 kb/s);? Ethernet 10Base2 (coaxial);? Ethernet 10BaseT (UTP, 10 Mb/s);? RS-232 (EIA-232, up to 115 kb/s);? RS-485 (EIA-485, up to 10 Mb/s);? user defined single wire or balanced system. Modes:: Waveform Parameter analysis with automatic read-out and parameter? validation (good / weak / bad); test limits are based on industry standards or may be set by the user.? Eyepattern display mode. Measured parameters (where applicable):: ? baud rate,? risetime,? fall time,? high level,? low level,? bias voltage level,? signal amplitude,? distortion,? jitter. Eyepattern display mode:: Gives waveform display of bus signals with display persistence. Timebase and attenuator settings may be altered by the user. Measurement types:: ? Watt,? VA,? VAR,? Power Factor (PF) Power configuration:: Single phase or balanced three-phase (delta-configuration) mains supply Voltage measurement:: Channel A; using STL120, voltage probe or direct input Current measurement:: Channel B, using i400s (included) or other compatible current clamp Current Clamp or Shunt sensitivity:: 0.1 / 1 / 10 / 100 / 1000 mV/A, 10 mV/mA and 400 mV/A : Converts waveform information into a harmonics display (using FFT processing) which shows the relative amplitudes of the 1st up to the 33rd harmonic Harmonics Frequency range:: DC up to 33rd harmonic (for fundamental up to 60 Hz);DC up to 24th harmonic (for fundamental up to 400 Hz). Display: Bargraph showing 1st up to 33rd harmonic and DC; amplitude displayed in % relative to fundamental Measurements:: Relative amplitude of individual harmonics;THD in %r or %f. Operating Temperature: 0 ?C to 50 ?C Storage Temperature: -20 ?C to +60 ?C Operating Altitude: 3,000 m Electrical Safety: 600V CAT III (EN61010-1) | Oscilloscope Bandwidth: bFluke 125:/b 40 MHzbFluke 124:/b 40 MHzbFluke 123:/b 20 MHz Dual input True RMS Meter: Vdc, Vac, Vac+Vdc, Ohms,Continuity , Diode-testCurrent, ?C, ?F, Capacitance, dBV, dBM, Crest Factor, Touch Hold and Zeroset TrendPlot Recording: Automatic vertical scaling and time compression.Display the actual, MIN, MAX and AVG reading. Cursors: bFluke 125/124:/b ?T, 1/?T, V, ?V, rise- and fall time Real-time sample rate: 25 MS/s Equivalent sampling rate: up to 2.5 GS/s (125, 124) or 1.25 GS/s (123) Inputs and digitizers: 2 Timebase range: bFluke 125/124:/b 20 ns - 1 min/divbFluke 123:/b 10 ns - 1 min/div Input sensitivity: 5 mV - 500 V/div Trigger types: Connect-and-View?, Free Run, Single Shot, Edge, Video, External Trigger types: Connect-and-View, Free Run, Single Shot, Edge, Video, External Glitch capture: 40 ns Scope measurements: Automatic measurements: 26 (all instruments) On top, Fluke 125 has additional measurement functions for Power (W), VA, VAR and Power Factor (PF) for single phase and balanced-three-phase (delta) power systems. Harmonics mode: Fluke 125 has capbility to analyze the harmonics contents of power signals. See below for details Maximum record length: 512 min/max pts per input Memory: 512 min/max pts per input Memory: bFluke 125/124:/b 20 screens and setupsbFluke 123:/b 10 screens and setups Measurement types:: ? Watt,? VA,? VAR,? Power Factor (PF) Power configuration:: Single phase or balanced three-phase (delta-configuration) mains supply Voltage measurement:: Channel A; using STL120, voltage probe or direct input Current measurement:: Channel B, using i400s (included) or other compatible current clamp Current Clamp or Shunt sensitivity:: 0.1 / 1 / 10 / 100 / 1000 mV/A, 10 mV/mA and 400 mV/A : Converts waveform information into a harmonics display (using FFT processing) which shows the relative amplitudes of the 1st up to the 33rd harmonic Analyzed waveform:: Voltage waveform(Ch.A), Current wavefrom (Ch.B) or Power (Ch.A x Ch.B), automatically generated. Harmonics Frequency range:: DC up to 33rd harmonic (for fundamental up to 60 Hz);DC up to 24th harmonic (for fundamental up to 400 Hz). Display: Bargraph showing 1st up to 33rd harmonic and DC; amplitude displayed in % relative to fundamental Measurements:: Relative amplitude of individual harmonics;THD in %r or %f. Operating Temperature: 0 ?C to 50 ?C Storage Temperature: -20 ?C to +60 ?C Operating Altitude: 3,000 m Electrical Safety: 600V CAT III (EN61010-1) | Oscilloscope Bandwidth: bFluke 125:/b 40 MHzbFluke 124:/b 40 MHzbFluke 123:/b 20 MHz Dual input True RMS Meter: Vdc, Vac, Vac+Vdc, Ohms,Continuity , Diode-testCurrent, ?C, ?F, Capacitance, dBV, dBM, Crest Factor, Touch Hold and Zeroset TrendPlot Recording: Automatic vertical scaling and time compression.Display the actual, MIN, MAX and AVG reading. Cursors: bFluke 125/124:/b ?T, 1/?T, V, ?V, rise- and fall time Real-time sample rate: 25 MS/s Equivalent sampling rate: up to 2.5 GS/s (125, 124) or 1.25 GS/s (123) Inputs and digitizers: 2 Timebase range: bFluke 125/124:/b 20 ns - 1 min/divbFluke 123:/b 10 ns - 1 min/div Input sensitivity: 5 mV - 500 V/div Trigger types: Connect-and-View?, Free Run, Single Shot, Edge, Video, External Trigger types: Connect-and-View, Free Run, Single Shot, Edge, Video, External Glitch capture: 40 ns Scope measurements: Automatic measurements: 26 (all instruments) On top, Fluke 125 has additional measurement functions for Power (W), VA, VAR and Power Factor (PF) for single phase and balanced-three-phase (delta) power systems. Harmonics mode: Fluke 125 has capbility to analyze the harmonics contents of power signals. See below for details Maximum record length: 512 min/max pts per input Memory: 512 min/max pts per input Memory: bFluke 125/124:/b 20 screens and setupsbFluke 123:/b 10 screens and setups Measurement types:: ? Watt,? VA,? VAR,? Power Factor (PF) Power configuration:: Single phase or balanced three-phase (delta-configuration) mains supply Voltage measurement:: Channel A; using STL120, voltage probe or direct input Current measurement:: Channel B, using i400s (included) or other compatible current clamp Current Clamp or Shunt sensitivity:: 0.1 / 1 / 10 / 100 / 1000 mV/A, 10 mV/mA and 400 mV/A : Converts waveform information into a harmonics display (using FFT processing) which shows the relative amplitudes of the 1st up to the 33rd harmonic Analyzed waveform:: Voltage waveform(Ch.A), Current wavefrom (Ch.B) or Power (Ch.A x Ch.B), automatically generated. Harmonics Frequency range:: DC up to 33rd harmonic (for fundamental up to 60 Hz);DC up to 24th harmonic (for fundamental up to 400 Hz). Display: Bargraph showing 1st up to 33rd harmonic and DC; amplitude displayed in % relative to fundamental Measurements:: Relative amplitude of individual harmonics;THD in %r or %f. Operating Temperature: 0 ?C to 50 ?C Storage Temperature: -20 ?C to +60 ?C Operating Altitude: 3,000 m Electrical Safety: 600V CAT III (EN61010-1) |