| Model |
DS1102E |
DS1052E |
DS1102D |
DS1052D |
| Bandwidth |
100 MHz |
50 MHz |
100 MHz |
50 MHz |
| Acquisition |
| Sample Modes |
Real-Time Sample |
Equivalent Sample |
| Sample Rate |
1GSa/s [1] , 500MSa/s |
| DS1102X |
DS1052X |
| 25GSa/s |
10GSa/s |
| Inputs |
| Input Coupling |
DC, AC, GND |
| Input Impedance |
1MΩ±2%, the input capacity is 18pF±3pF |
| Probe Attenuation Factors |
1X, 5X, 10X, 50X, 100X, 500X,1000X |
| Maximum Input Voltage |
400V (DC+AC Peak, 1MΩ input impedance)
40V (DC+AC Peak) [2] |
| Time Delay between Channel (typical) |
500ps |
| Horizontal |
| Sample Rate Range |
Real-Time: 13.65Sa/s-1GSa/s
Equivalent: 13.65Sa/s-25GSa/s |
| Waveform Interpolation |
Sin(x)/x |
| Memory Depth |
Channel Mode |
Sample Rate |
Memory Depth (normal) |
Memory Depth (long memory) |
| Single Channel |
1 GS/s |
16 kpts |
N/A |
| Single Channel |
500MS/s Or lower |
16 kpts |
1 Mpts |
| Dual Channel |
500MS/s Or lower |
8 kpts |
N.A. |
| Dual Channel |
500MS/s Or lower |
8 kpts |
512 kpts |
| Scanning Speed Range (Sec/div) |
2ns/div~50s/div, DS1102X
5ns/div~50s/div, DS1052X
1-2-5 Sequence |
| Sample Rate and Delay Time Accuracy |
±50ppm (any interval ≥1ms) |
| Delta Time Measurement Accuracy (Full Bandwidth) |
Single: ±(1 Sample interval + 50ppm × reading + 0.6 ns)
>16 averages: ±(1Sample interval + 50ppm × reading + 0.4 ns) |
| Vertical |
| A/D Converter |
8-bit resolution, all channels sample simultaneously |
| Volts/div Range |
2mV/div~10V/div (at the input terminal connecting to BNC) |
| Maximum Input |
Maximum input voltage on analog channel
CAT I 300Vrms, 1000Vpk; instantaneous overvoltage 1000Vpk
CAT II 100Vrms, 1000Vpk
RP2200 10:1:CAT II 300Vrms
RP3200 10:1:CAT II 300Vrms
RP3300 10:1:CAT II 300Vrms |
| Offset Range |
±40V (250mV/div~10V/div)
±2V (2mV/div~245mV/div) |
| Analog Bandwidth |
100MHz (DS1102D,DS1102E)
50MHz (DS1052D, DS1052E) |
| Single-shot Bandwidth |
100MHz (DS1102D, DS1102E)
50MHz (DS1052D, DS1052E) |
| Selectable Analog Bandwidth Limit (typical) |
20MHz |
| Lower Frequency Response (AC –3dB) |
≤5Hz (at input BNC) |
| Rise Time at BNC (typical) |
<3.5ns, <7ns, respectively at 100MHz, 50MHz |
| Dynamic range |
±5div |
| DC Gain Accuracy |
2mV/div-5mV/div:
±4% (In Normal or Average acquisition mode)
10mV/div-10V/div:
±3% (In Normal or Average acquisition mode) |
| DC Measurement Accuracy, Average Acquisition Mode |
When vertical displacement is zero, and N ≥16: ±(DC Gain Accuracy×reading+0.1div+1mV)
When vertical displacement is not zero, and N ≥16: ±[DC Gain Accuracy×(reading+vertical displacement)+(1% of vertical displacement) + 0.2div]
When vertical scale is between 2mV/div and 245mV/div, add 2mV more for setting value.
When vertical scale is between 250mV/div and 10V/div, add 50mV more for setting value. |
Delta Volts
Measurement Accuracy
(Average Acquisition Mode) |
Under same setting and condition, the voltage difference (?V) between any two points in the waves coming from the average of more than 16 waves have been acquired: ±(DC Gain Accuracy×reading + 0.05 div) |
| Trigger |
| Trigger Sensitivity |
0.1div~1.0div (adjustable) |
| Trigger Level Range |
Internal |
±6 divisions from center of screen |
| EXT |
±1.2V |
| Trigger Level Accuracy (typical) applicable for the signal of rising and falling time ≥20ns y |
Internal |
±(0.3div × V/div)(±4 divisions from center of screen) |
| EXT |
±(6% of setting + 200 mV) |
| Trigger Offset |
In Normal mode: pre-trigger (memory depth/ 2*Sample rate), delayed trigger 1s |
| In Slow Scan mode: pre-trigger 6div, delayed trigger 6div |
| Trigger Holdoff Range |
500ns~1.5s |
| Set Level to 50% (typical) |
When input signal frequency ≥50Hz |
| Edge Trigger |
| Edge trigger slope |
Rising, Falling, Rising + Falling |
| Pulse WidthTrigger |
| Trigger Condition |
(>, <, =) Positive pulse width, (>, <, =) Negative pulse width |
| Pulse Width Range |
20ns ~10s |
| Video Trigger |
| Video Standard Line Frequency |
Support for standard NTSC, PAL and SECAM broadcast systems. Line number range: 1~525 (NTSC) and 1~625 (PAL/SECAM) |
| Slope Trigger |
| Trigger Condition |
(>, <, =) Positive slope, (>, <, =) Negative slope |
| Time Setting |
20ns~10s |
| Alternate Trigger |
| Trigger on CH1 |
Edge, Pulse Width, Video, Slope |
| Trigger on CH2 |
Edge, Pulse Width, Video, Slope |
| Pattern Trigger [2] |
| Pattern Type |
D0~D15 select H, L, X, , |
| Duration Trigger [2] |
| Pattern Type |
D0~D15 select H, L, X |
| Qualifier |
>, <, = |
| Time Setting |
20ns~10s |
| Measurements |
| Cursor |
| Manual |
Voltage difference between cursors (∆V)
Time difference between cursors (∆T)
Reciprocal of ∆T in Hertz (1/∆T) |
| Track |
Voltage value for Y-axis waveform
Time value for X-axis waveform |
| Auto |
Cursors are visible for Automatic Measurement |
| Auto Measure |
Vpp, Vamp, Vmax, Vmin, Vtop, Vbase, Vavg, Vrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Time, +Width, -Width, +Duty, -Duty, Delay1→2 , Delay1→2 |