| FEATURES |
| Display |
2 vacuum fluorescent graphical displays, 16x140 pixels |
| Memories |
100 sequences of 100 registers plus system memories |
| Sweep Features |
Linear, octave, and decade of up to 10,000 points |
| Scanner Mode |
Allows scanning through a sequence of 100 stores |
| SINAD Meter |
Displays reading from -30dB to 0dB of SINAD |
| IF Freq. Counter |
Measures frequency error to 1Hz in three counter modes |
| Battery Meter |
Displays charge left in batteries |
| Reverse Protection |
Generator output protected, switches into 100W internal load and automatically displays power in dBm or watts. |
| Power Meter |
Displays power from +23dBm to +50dBm, ± .5dB (200mW-100W) |
| Attenuator Output |
-30dB sample port from load for external equipment |
| RSSI Meter |
80dB of range on receiver side, -40dBm to -120dBm |
| Warranty |
One-year parts and labor with extended Ramsey Technical Support and dedicated COM3010 user forum access |
| GENERATE MODE |
| Frequency |
100kHz to 1.0GHz in 1Hz steps |
| Freq. Accuracy |
± 0.1 ppm standard |
| RF Output Level |
-140dBm to 0dBm in 0.1dBm steps |
| Level Accuracy |
± 1dB, 500kHz to 1GHz, ±2dB 100kHz to 500kHz |
| Units |
dBm, uV, mV |
| Leakage |
Better than 1uV, 2 turn loop, 1" diameter at 1” |
| Spurious Harmonics |
-30dBc typical |
| Non-harmonics |
-50dBc typical |
| FM Modulation |
± 75kHz max in 0.1Hz steps |
| FM Bandwidth |
0.1Hz - 75kHz |
| Accuracy |
± 0.1ppm (inherently tied to reference frequency) |
| AM Modulation |
0 - 75% in 1% steps to -100dBm, 0-50% to -140dBm |
| AM Bandwidth |
10Hz - 10kHz |
| Accuracy |
± 5% |
| Distortion |
Less than 5% |
| Modulation Internal |
0.1Hz - 3 kHz |
| Modulation External |
0.1Hz - 3 kHz digital and analog selectable, auto leveling. |
| CTS Encode |
0.1Hz to 999.9Hz at ±.75kHz default deviation, variable from .1Hz to 2kHz deviation |
| DPL Encode |
±750Hz, all supported codes |
| RECEIVE MODE |
| Frequency |
100kHz to 1.0GHz in 10Hz steps |
| Sensitivity |
Less than 2uV below 512MHz
Less than 3uV above 512MHz |
| FM Demod |
0 - 7 kHz, 0 - 4kHz |
| AM Demod |
0-100% |
| CTS Decode |
In AF frequency count |
| Frequency Error |
0-1MHz, two methods of bargraph and count |
| AF Demod output |
1Vp-p for 7kHz deviation |
| Gates |
0.1 sec, 1 sec |
| FREQUENCY COUNTER |
| Frequency Range: |
100kHz - 1GHz |
| Low Band Sensitivity: |
Less than 5mV under 50MHz, less than 10mV under 70MHz, 1Hz and 10Hz resolutions |
| High Band Sensitivity: |
Less than 6mV over 200MHz to 1.0GHz, less than 10mV 70MHz to 200MHz, 10Hz and 100Hz resolutions with divide by ten prescaler |
| IF Frequency: |
Receiver sensitivity, range limited to bandwidth of current set receiver frequency ±10kHz, 1Hz, and 10Hz resolutions |
| AUDIO COUNTER |
| Frequency Range: |
60Hz-3000Hz |
| Gates: |
10 Sec variable gate for 1 sec quick updates |
| Sensitivity: |
35mV at demod audio, (± 750Hz deviation) |
| GENERAL |
| Receiver input: |
Has diode protection and fused components |
| Controls: |
Elastomeric keypad |
| Dummy Load: |
100W 30dB feed-through attenuator with sample port on rear, 25% duty cycle full power |
| RS232 Control: |
Serial interface provides external function control and automated calibration |
| Primary power: |
100-240VAC, .6A, 50/60 Hz; built in Li-Ion battery |
| Stand: |
Bottom mounted tilt-bail stand included |
| Case Color: |
Mist gray epoxy powder coat |
| Supplied Accessories: |
110VAC EIA cord, BNC-BNC test cable, whip antenna, one BP3010 Li-Ion battery |
| Dimensions: |
6” H x 11.9375” W x 14.75” D (152.4mm H x 303.31mm W x 374.65mm D) |
| Weight: |
14 lbs (6.5kg) |
;)
