Protek
6510 100MHz Oscilloscope

Click image to enlarge Protek 6510 Data sheet User guide Selection Guide / Accessories

Features: Four traces may be simultaneously displayed in ALT-sweep Five vertical display modes: CH1, CH2, Dual, Add, Subtract Vertical mode triggering for displaying 2 unrelated signals Trigger hold-off circuit for synchronizing complex waveforms Sweep speeds to 2nS/Div 12kV acceleration voltage for bright displays of low duty cycle signals Z axis input TV Synchronization for either line or field patterns 20MHz bandwidth limit switch for triggering signals in a noisy environment

Model	Description	List Price	Sale Price
6510	100 MHz 2Ch. Dual Time Base with Alt Mag.	$975.00	$838.50
Model	Accessories	List Price	Sale Price
PP80	DC to 60MHz hook-on X1/X10 Probe - Discontinued - suggested replacement: CalTest CT2704
PP150	DC to 100 MHz hook-on X1/ X10 Probe	$39.00	$33.54

Vertical Amplifier (CH 1 and CH 2)
Sensitivity	5 mV/Div to 5 V/Div in 7 calibrated steps, (X5 Mag 1mV/Div to 1 V/Div)
Accuracy	±3% (±5% in X5 Mag)
Bandwidth (-3dB)	DC to 100MHz
Rise Time	£ 3.5 ns, X5 Mag: 20MHz Bandwidth: £ 17 ns
Input Impedance	1MW + 25 pF
Input Coupling	AC-Gnd-DC
Invert Channel	CH2
Display Modes	CH1, CH2, Add, Subtract, Dual (Alt/Chop)
Maximum Input Voltage	400V (DC or AC peak)
CH1 Signal Output	20mV into 50W
Horizontal Sweep
Timebase A - Sweep Time	50ns/Div to 0.2 s/Div in 21 calibrated steps (1-2-5)
Timebase A - X10 Mag	5ns/Div to 20ms/Div
Timebase A - Accuracy	±3% (± 5% in X10 Mag)
Timebase A - Hold Off	Continuously adjustable to > 2X sweep time
Timebase B - Sweep Time	50ns/Div to 10µs/Div in 8 steps (1-2-5)
Timebase B - Accuracy	±3%
Timebase B - Delay Time	Continuously variable from 0.2µs to 2s
Timebase B - Delay Modes	Continuous or triggered
Timebase B - Sweep Displays	A, B, A alt B, B triggered, X-Y
X-Y Mode
CH1-X axis, CH2-Y axis Sensitivity	Same as CH1 vertical amplifier
Bandwidth (X-axis)	DC to 2MHz
Phase Error	£ 3° DC to 10kHz
Triggering
Trigger Modes	Auto, Normal, TV-V, TV-L
Source	Int. CH2, line ext.
Coupling	AC
Slope	Positive or negative
Trigger Sensitivity	Int (DC to 10MHz): 0.5 Div Int (10MHz to 100MHz): 1.5 Div Ext (DC to 10MHz): 200mV Ext (10MHz to 100MHz): 500mV TV (Int):1 Div Min TV (Ext): 1V P-P
External Trigger Input	Impedance: 1MW + 20 pF Maximum Input Volts: 400V DC or AC peak
Z Axis Modulation
Sensitivity	±5V P-P Intensity increases with a negative going voltage input
Bandwidth (-3dB)	DC to 2MHz
Input Impedance	Approx. 2 KW
Calibrator Signal
Voltage	0.5V ±3% P-P 1kHz Square Wave
Duty Cycle	Approx. 50%
CRT
Type	6" rectangular CRT with internal graticule. (1 Div = 1cm)
Acceleration Voltage	12 kV
General Specification
Power Requirements	AC Input Voltage: 100V, 120V, 220V, 240V selectable
Frequency	50/60Hz
Power Consumption	55W
Operating Temperature	0 to 40°C at 35% to 85% relative humidity
DIMensions	5.25" H × 12.67"W × 14.5" D
Weight	24 lbs.
Supplied Accessories	Manual, 1 AC Power cord, (2) X10 Probes

Protek Main Page

Protek Oscilloscopes

Protek Price List