Our agents are available:
9:00 AM - 6:00 PM EST
PIE Model 532 4-20 mA/Voltage Loop Calibrator with Loop Diagnostics
   Search: HACKER SAFE certified sites prevent over 99.9% of hacker crime.
   
   
   
PIE Model 532 4-20 mA/Voltage Loop Calibrator with Loop Diagnostics


PIE Model 532
Click image to enlarge

PIE 532

Datasheet
Instructions

 Features:
  • True ±0.012% of reading accuracy
  • Source and Read 0.000-24.000 mA
  • Simulate 2-Wire Transmitters
  • Power 2-Wire Transmitters and Read 0.000-24.000mA
  • Display current in mA or -25.00-125.00 % of 4-20 mA
  • Read 0.00 to ± 30.00 VDC with 4X over range ability
  • Source 0.000 to 24.000 VDC with up to 20mA output
  • Direct Calibration 1.000V to 5.000V
  • Auto Step or Ramp
  • Selectable step sizes, time in-between steps & soak time
  • Stop watch like EZ-Check switch
  • Full 5 Digit Display
  • Uses 1 - 9Volt alkaline battery
  • Superior battery life of 40 hours under typical continuous usage
  • Easy access to battery compartment
  • 240 VAC Tolerant
  • HART protocol compatibility mode
  • Uses 4 AA alkaline batteries
  • Power on selectable 250ω resistor in series with the output for compatibility with HART® protocol enabled devices.
  • NIST Traceable Calibration Certificate included FREE


  Description

The Practical Instrument Electronics’ Model 532 is the best tool for calibration, test, and diagnosing process loops. The Model 532 brings all the features you would expect from a loop calibrator and timesaving new ones. Make adjustments with the EZ-Dial Knob or test limits with the dual action EZ-Check Switch. Powerful ramping functions are only a button away on the Model 532. Save potentially hours of troubleshooting time on problem loops with the 532’s unique Loop Diagnostic Mode.

In Loop Diagnostic Mode, the loop current, voltage, resistances, AC voltage, and mode of operation are all displayed simultaneously; without the need of multiple DMM connections. Loop diagnostic is available in every mode of operation and truly is a diagnostic monitor, as parameters are continuously updated in real time. The smart diagnostic tool even indicates the most likely cause of loop failure!

The Model 532 can detect loop current, voltage, resistance, AC voltage and HART protocol if present in the loop. You are able to connect the 532 to either side of the loop and in every operation mode diagnose what is happening in the loop without the need of a DMM. Just press the loop diagnostic button once connected and see if there is a problem with the loop.



  Models, Options, & Accessories


Model Description List Price Sale Price
532 4-20 mA/V Calibrator with Loop Diagnostic (Includes Carrying Case) $995.00
$945.25 
Model Accessories List Price Sale Price
020-0100 AC Adaptor for models 530 & 532 (230V, 50Hz) $40.00
$38.00 
020-0101 AC Adaptor for models 530 & 532 (120V, 60Hz) $40.00
$38.00 
020-0204 Carrying Case w/PIE LOGO for models 530, 532, 535 & 541 $40.00
$38.00 


  Specifications

General Specifications: (Unless otherwise indicated all specifications are rated from a nominal 23 °C, 70 % RH for 1 year from calibration)
Temperature Range -25 to 60 °C (-5 to 140 °F)
Storage Temperature Range -30 to 60 °C (-22 to 140 °F)
Relative Humidity Range 10 % 10 %
Size 7.00 X 3.30 X 2.21 inches (177.8 x 83.8 x 56.1mm)
Weight 12.0 oz (340 grams)
Battery 9V Alkaline
Optional 120 VAC 50/60 Hz AC adaptor available
Miscellaneous Low battery indication with nominal 1 hour of operation left
Over-voltage protection to 120 Vrms (rated for 30 seconds) or 240 Vrms (rated for 15 seconds)
Bar graph display with 1% resolution of 4-20 mA signal scale
High contrast graphic liquid crystal display with 0.45 (11.4 mm) high digits
Model 535A Analog Output 10 mV/mA ±(0.1% + 0.04mV), 5 ppm/°C
Common Specifications for all current modes:
Ranges 0.000 to 24.000 mA, -25.00 to 125.00% of 4-20 mA
Accuracy < ± (0.012 % of reading + 0.002 mA)
Temperature effect < ± 50 ppm/°C of range
Resolution 0.001 mA and 0.01 %
Source/Power and Measure 2-Wire Transmitter Specifications:
Loop Compliance Voltage > 24 Volts
Loop Drive Capability 1200 ω at 20 mA for entire battery life, 950ω w/HART mode enabled
Miscellaneous Open loop or out of compliance conditions are indicated by appropriate error display

Battery Life in:
Source mode > 18 hrs at 12mA typical (HART disabled)
Power measure > 10 hrs at 12mA typical

HART protocol mode is a selectable option at turn on. HART protocol mode places a 250Ω resistor in series with the output:
Selectable EZ-Step(s) for Source Mode/2-Wire Transmitter Simulation:
2 to 16 selectable step settings
Step size is determined by the selected high & low ranges
Selectable time settings for stepping and soak:
STEP: 5 to 900 seconds
SOAK: 0 to 900 seconds
Read mA Specifications:
Voltage burden < 2V at 20 mA
Overload/Current limit protection nominal < 24 mA
Battery life typical > 40 hours
2-Wire Transmitter Simulation Specifications:
Voltage Burden < 2 V at 20 mA
Overload/Current Limit Protection nominal < 24 mA
Loop Voltage Limits 2-60 VDC
Miscellaneous Open loop or out of compliance conditions are indicated by appropriate error display

Battery life = 40 hour typical
Selectable EZ-Step(s) for Source Mode/2-Wire Transmitter Simulation:
2 to 16 selectable step settings

Step size is determined by the selected high & low ranges
Selectable time settings for stepping and soak:
STEP: 5 to 900 seconds SOAK: 0 to 900 seconds
Voltage Specifications (Read Range):
Read Range 0.000 to 24.000 VDC then 24.01 to 30.00 (with 4X over range) Auto Ranging
Resolutions 0.001 V up to 24 V, 0.01 V up to 30.00 V
Temperature Effect < ± 100 ppm/°C of range
Input Resistance > 1 Mω
Accuracy 0.000 to 24.000 VDC = ± (0.012%RDG + 0.004 V)
24.01 to 30.00 VDC = ± (0.025 % of reading ±0.04 V)
Voltage Specifications (Source Range):
Source Range 0.000 to 24.000 VDC
Output Resistance <0.3ω
Source Current > 20.000 mA with Flashing indicator for over range
Accuracy <±(0.012%RDG + 0.004 V) ±50ppm/°C of range
Battery Life > 40 hour typical

   
  Welcome | Companies | Search by Type | How To Order | Leasing | About Us  
  Tequipment.NET
205 Westwood Ave
Long Branch, NJ 07740
For our Electronic Whiteboard division visit www.touchboards.com 		BBBOnline Reliability Seal. Tequipment.NET
Phone: 1-877-742-TEST (8378) / 732-222-7077
Fax: (732) 222-7088
E-mail: salesteam@Tequipment.NET