| Standards |
| Input/output slot |
| Dedicated slot for input unit (Slot 1 and Slot 2) |
2 systems |
| I/O slot for input/output unit (Slot 3 and Slot 4) |
2 systems |
| Supported units |
LV58SER01A (SDI input)
LV58SER02 (Eye Pattern) *1
LV58SER03 (Composite input)
LV58SER04 (MPEG decoder)
LV58SER06 (3G SDI input
LV58SER20 (DVI-I output)
LV58SER21 (Analog component output)
LV58SER40A (Digital audio) *1
*1 can only install one card per unit/platform. |
| DVI-I output connector |
| Output connector |
DVI-I 1 system |
| Signal format |
Single Link T.M.D.S
Analog RGB |
| Display format |
XGA (Active picture area 1024 x 768 dot)
Compliance wide screen display (Squeeze format) |
| DDC function |
Does not compliance |
| HOT PLUG function |
Does not compliance |
| Screen capture |
| Capture function |
Screen capture of displayed screen (Stores one picture in the internal memory) |
| Media |
Internal memory of the mainframe (RAM), USB memory |
| Data output |
USB memory or via Ethernet |
| Preset |
| Number of preset |
50 |
| Media |
Internal memory of the mainframe (RAM), USB memory |
| Recall method |
Front panel, memory connector, Ethernet |
| Copy preset data |
Copy preset data to USB memory |
| Copy preset data to USB memory |
Recall preset data stored in the USB memory to the internal memory of the mainframe. |
| External synchronization input |
| Input connector |
BNC connector 1 system 2 connectors |
| Input signal |
Tri-level signal or NTSC/PAL black burst signal |
| Input impedance |
15kohm pass through |
| Input return loss |
30dB above |
| Maximum input voltage |
+/- 5V (DC + Peak AC) |
| External remote control connector |
| USB connector |
| Standard |
2.0 |
| Device |
Support big capacity memory only |
| Function |
Screen capture, data storage, preset data storage |
| Ethernet connector |
| Standard |
IEEE 802.3 10BASE-T/100BASE-T |
| Connector |
RJ-45 |
| Function |
Remote operation using external PC, screen capture, data storage, error monitor |
| Parallel remote connector |
| Standard |
D-Sub25 pin (Female) |
| Signal |
LV-TTL level (LOW ACTIVE) |
| Function |
Preset recall, error detection, input switching, analog audio input *1
*1 When measuring the analog audio, LV58SER40A (Digital Audio) card is needed. |
| Head phone output |
| Output connector |
6.3 mm standard jack (Stereo) *1
*1 Only valid when LV58SER40A (Digital Audio) card is installed. |
| Video Formats and Corresponding Standards |
| Ancillary data standard |
SMPTE 291M |
| Embedded audio standard |
HD-SDI: SMPTE 299M SD-SDI: SMPTE 272M |
| Format Setting |
Automatic setting (In a dual link mode, only frame / field frequency is set automatically.) |
| Input/Output Connector |
SDI Input |
| Input Connector |
BNC connector 2 connectors
For single link A ch / B ch 2 systems
For dual link link A / link B 1 system |
| Input Impedance |
75 |
| Input Return Loss |
15 dB or more 5 MHz to serial clock frequency |
| Maximum Input Voltage |
}2 V (DC + peak AC ) |
| SDI Output |
| Output Connector |
BNC connector 2 connectors
Reclocks serially and outputs the input signal.
For dual link link A / link B 1 system |
| Output Impedance |
75 |
| Output Voltage |
800 mVp-p }10 % |
| Output Return Loss |
15 dB or more 5 MHz to serial clock frequency |
| Waveform Display Function |
| Waveform Operation |
Display Mode |
| Overlay display |
Displays component signals overlaid |
| Parade display |
Displays component signals side by side |
| Gain Adjustment |
x1 / x5 / variable |
| Blanking Period |
Show / hide selectable |
| YCBCRGBR conversion |
Converts YCBCR signals into GBR and displays the result. |
| Pseudo-Composite Display |
Artificially converts component signals into composite signals and displays the result. |
| Timing Display |
Displays by calculating Y-CB and Y-CR |
| Uses bowtie signals (authorised by Tektronix, inc.) |
| Channel Assignment |
Selects GBR order or RGB order during GBR conversion display |
| Line Select |
Displays the selected line |
| Image Quality Adjustment |
Contrast adjustment, Brightness adjustment |
| Vertical axis |
| Sensitivity |
V scale 0 V to 0.7 V, -0.3 V to 0.7 V |
| % scale 0 % to 100 %, -50 % to 100 % |
| Gain |
x1, x5, and variable |
| Variable Gain |
x0.2 to x10 |
| Amplitude Accuracy |
+0.5 % |
| Frequency Response HDTV |
| Y Signal |
+0.5 % 1 MHz to 30 MHz |
| CB, CR Signal |
+0.5 % 0.5 MHz to 15 MHz |
| Low-pass Attenuation |
20 dB or more at 20 MHz |
| Frequency Response SDTV |
| Y Signal |
}0.5 % 1 MHz to 5.75 MHz |
| CB, CR Signal |
}0.5 % 0.5 MHz to 2.75 MHz |
| Low-pass Attenuation |
20 dB or more at 3.8 MHz |
| Horizontal Axis |
Line Display:
Display Format |
Overlay: 1H, 2H |
| Parade |
1H, 2H, 3H |
| Timing |
Y-CB,Y-CR |
| A/B Overlay*1 |
1H, 2H, 3H |
| 4Y Parade*2 |
4H |
| Magnification |
Selects x1, x10, x20, ACTIVE, or BLANK
*1 A/B overlay mode needs to synchronize mutually in the same format also as A input/ B input.
*2 As for 4Y parade mode, two LV 58SER01 (SDI INPUT unit) should be inserted, and four inputs need to synchronize in the same format each other together. |
|
| Field Display |
| Display Format |
Overlay: 1V, 2V (2V display not allowed for progressive) |
| Parade |
1V, 2V, 3V |
| Magnification |
x1, x20, x40 |
| Time Base Accuracy |
}0.5 % |
| Cursor Measurement |
| Configuration |
Horizontal cursors: 2 cursors (REF and DELTA) |
| Vertical cursors |
2 cursors (REF and DELTA) |
| Amplitude Measurement |
Measured in [%] and [V] |
| Time Measurement |
Displayed in [usec] or [msec] |
| Frequency Display |
Displays the frequency in which the time between cursors is considered a cycle. |
| Vectorscope Display |
| Sensitivity |
Selects 75 % or 100 % (Using a color bar) |
| Gain |
Selects x1, x5, IQ-MAG or variable |
| Variable gain |
x0.2 to x10 |
| Amplitude Accuracy |
+0.5 % |
| EAV-SAV Period |
Operation of "Show or hide" is being linked to the waveform display. |
| IQ Axis |
Selects show or hide |
| Pseudo-Composite Display |
Artificially converts component signals into composite signals which added BURST and displays the result. (the color matrix for HDTV signal is converted into SDTV) |
| Image Quality Adjustment |
Contrast adjustment, Brightness adjustment |
| Phase Difference Display |
| Display |
The phase difference between SDI signal and external sync signal is displayed by the numerical value and graphic. |
| Display Range |
V direction +1 Field (for interlace)
+ 1/2 Frame (for progressive)
H direction + 1/2 Line
*The phase difference display in the H direction may fluctuate in the range of +1 clock when the signal is switched. |
| Sync Signal |
HD tri-level sync signal or black burst signal |
| Picture Display |
| HDTV Display |
Displayed by sampling the pixels (R, G, and B are both same 8 bits) |
| SDTV Display |
Displayed by interpolating pixels (R, G, and B are both same 8 bits) |
| Marker Display |
Center marker
4.3 or 16:9 marker display
Safe action marker display
Safe title marker display
Safe title marker display |
| Line Select |
Displays the selected line as a marker |
| Image Quality Adjustment |
GBR gain adjustment, Contrast adjustment, Brightness adjustment |
| Status Display |
| Status Display of SDI Signal |
| Signal Detection |
Detects the presence or absence of SDI signals. |
| Format |
Detection from correspondence video signal format |
| Equivalent Cable Length Measurement |
Converts the SDI signal attenuation into a coaxial cable length and displays the result. |
| Embedded Audio Channel |
Displays the embedded audio channel number. |
| Phase Difference Measurement for Dual Link |
Displays the phase difference between link A and link B as a number of parallel clocks.
The error of +1 clock is included.
Error Detection of SDI signals. |
| CRC Error |
Detects transmission error of HD-SDI signals. |
| EDH Error |
Detects transmission error of SD-SDI signals. |
| TRS Error |
Detects TRS errors. |
| Line Number Error |
Line number errors in the HD-SDI signals are being detected. |
| Reserved Error |
Detects reserved area errors. |
| Embedded Prohibition Error |
Detects the presence or absence of embedded audio at the embedded prohibition line. |
| Cable Length Meter Error |
Detects the signal attenuation and displays the result. |
| Error Detection of Embedded Audio |
| BCH Error |
Detects transmission errors of embedded audio packets in the HD-SDI signal. |
| DBN Error |
Detects sequential errors in audio packets. |
| Parity Error |
Detects parity errors in audio packet. |
| Error Detection of Ancillary Data |
| Checksum Error |
Detects transmission errors of the ancillary data. |
| Parity Error |
Detects parity errors in the ancillary data header. |
| Image Evaluation |
| Gamut Error |
Detects the Gamut Errors by specifying time. |
| Upper limit |
90.0 % to 109.4 % (0.1 % steps) |
| Lower limit |
-7.2 % to +6.0 % (0.1 % steps) |
| Composite Gamut Error |
Monitors the level error when the component signal is converted into composite signal. |
| Upper limit |
90.0 % to 135.0 % (0.1 % steps) |
| Lower limit |
-40.0 % to -20.0 % (0.1 % steps) |
| Event Log |
| Number of Logs |
Error items, time stamps, Q signal, etc. |
| 5 Bar Display |
| Bar Display |
Displays the Y GBR component Gamut or composite Gamut |
| Analysis Function |
| Data Dump Display Display Format |
Displayed separately by serial data sequence or channel. |
| Line Select |
Displays the selected line |
| Sample Select |
Displays the selected sample |
| Jump Function |
Move to EAV or SAV by one-key operation |
| Data Output |
Save data in text format to a PC via a USB memory or Ethernet network. |
| Voice Control Packets |
| Display Content |
Analyzes and displays the voice control packets |
| Display Format |
Text / Hexadecimal number / Binary number |
| Group Selection |
One group is selected from four groups. |
| EDH Display |
| Standard Supported |
SMPTE RP-165 |
| Display Content |
Analyzes and displays the EDH packets. |
| Displays the received CRC errors. |
| Display Format |
Text / Hexadecimal number / Binary number |
| Format ID Display |
| Standard Supported |
SMPTE 352M ARIB STD-B39 |
| Display Content |
Analyzes and displays the Format ID. |
| Display Format |
Text / Hexadecimal number / Binary number |
| Closed Caption Data Display |
| Standard Supported |
ARIB STD-B37,EIA/CEA-608,EIA-708 |
| Display Content |
Analyzes and displays the closed caption data. |
| Display Format |
Text / Hexadecimal number / Binary number |
| Inter-Stationary Control Data (NET-Q) Display |
| Standard Supported |
ARIB STD-B39 |
| Display Content |
Analyzes and displays the Inter-Stationary Control Data. |
| Display Format |
Text / Hexadecimal number / Binary number |
| V-ANC User Data Display |
| Standard Supported |
ARIB TR-B23 |
| Display Format |
Text / Hexadecimal number / Binary number |
| Arbitrary ANC Packet Display |
| Method of Specifying ANC |
Selects DID or SDID |
| Display Format |
Text / Hexadecimal number / Binary number |
| Time Code Display |
| Corresponding Time Code |
Selects LTC or VITC SMPTE RP-188 |
| Display Method |
Switches the display of internal clock, and the time code. |
| Closed Caption Processing |
| The closed caption data that is multiplexed in the SDI signal can be overlaid on the picture display. |
| SMPTE System |
CEA/EIA-608-B embedded in the CDP packets as defined in CEA/EIA-708-B.
CEA/EIA-608-B,
VBI(CEA/EIA-608-B Line21). |
| Cable Length Measurement |
| Detection method |
Converts the SDI signal attenuation into a coaxial cable length and displays the result. |
| Supported Cables |
HD-SDI Selects L-7CHD, LS-5CFB, or 1694A
SD-SDI Selects LS-5C2V, 8281, or 1505A |
| Display Range |
HD-SDI: From under 5 m to 130 m or more
(For L-7CHD From under 10 m to 200 m or more)
SD-SD: From under 50 m to 300 m or more |
| Accuracy |
+20 m |
| Resolution |
5 m (For L-7CHD: 10 m) |
| Frame Capture Function |
| Media |
Internal memory (RAM) or USB memory |
| Internal Memory Capacity |
Video data 1 Frame 2 Systems |
| For Dual Link mode |
1Frame 1system |
| Data Output |
Save capture data to a PC via a USB memory or Ethernet network. |
| Recalling Capture Data |
Recalls and displays the Picture/ Waveform/
Vector of 1 frame capture data.
The capture data saved in the USB memory can be read back.
(Reading back operation cannot be performed when there is no SDI signal.) |
;)
;)
;)
;)
;)
;)
;)
