| Input Power |
0 to 150 W |
| Input Voltage Range |
CR Mode:0 to 200V, CC/CP/CV Mode:1.5 to 200V |
| Input Current Range(Front/Rear
Terminal) |
0 to 30A / 0 to 30A |
| Constant Current
Mode |
Range/Resolution |
H Range: 30A: 0 to 30A / 1mA 150W max
L Range: 0.3A: 0 to 0.3A / 10μA 1.5W max |
| Accuracy |
±0.2% of SET ±0.3% of FS (0
to 40°C) |
| Ripple Noise (1MHz) |
H Range 10mA rms / L Range 1mA rms |
| Stability |
±0.1% of FS (typ) |
| Constant Resistance
Mode |
Range |
H Range: OPEN, 1.5kΩ to 50mΩ
L Range: OPEN, 150kΩ to 5Ω |
| Resolution |
H Range: 0.66ms / L Range:6.6μs |
| Accuracy (23°C ±5°C) |
H Range: ±0.5% of SET ±0.15A
Vin/Rin
L Range: ±0.5% of SET ±1.5mA Vin/Rin |
| Ripple Noise (1MHz) |
H Range: 10mA rms / L Range: 1mA rms |
| Temperature Factor |
1000PPM/°C (Vin=5V) |
| Constant Voltage
Mode |
20V Range/200V Range |
1.5 to 20V/15 to 200V (CC CV Mode, CR CV
Mode) |
| Accuracy/ Resolution/ Minimum
Operating Current |
±0.1% of SET ±0.1% of FS (0
to 40°C) / 20V Range: 1mV, 200V Range: 10mV / 1% of Constant
Current |
| Constant Power Mode |
Operating Range/Resolution |
H Range: 3 to 150W / 5mW
L Range: 0.03 to 1.5W / 50μW |
| Accuracy (23°C ±5°C) |
±0.4% SET ±1.6%FS ±Vin
x Vin / Rin (Vin x Vin / Rin for Current L Range) (TEMP factor:
1000PPM/°C (Vin=5V)) |
| Ripple Noise (1MHz) |
H Range: 10mA rms / L Range : 1mA rms |
| Short Mode |
Setting Current Value |
0.3/30A (V1 model CC0V: 18A) |
| SW Mode (Preset
A,B) |
Frequency/Accuracy |
1Hz to 10kHz / ±1.5% SET |
| DUTY/ Setting Accuracy/ Resolution |
5% to 95% / ±1.5% SET / 1% STEP |
| Through Rate Tr/Tf |
Operating Mode |
CC, CR |
| Setting Range |
CC:10 / 20 / 50 / 100 / 200 / 500 / 1000
/ 2000μs, CR:OFF / 200 / 500 / 1000 / 2000μs |
| Setting Accuracy |
H: 10, 20μs :-5μs : ±10μs,
L: 10, 20μs : ±10μs, H: 50 to 2000μs : ±20
%, L: 50 to 2000μs : ±30% |
| Soft Start |
Operating Mode |
CC |
| Setting Range/Accuracy |
0.1 / 1 / 2 / 5 / 10 / 20 / 50 / 100ms /
±30 % of set 100μs |
| Remote Sensing |
|
2.5 V par One Way |
| External Control |
Voltage |
0 to 10V (Offset gain Adjustable at Rear
Panel. ) It takes approx. 1 Second for Settings at CR Mode |
| Resistance |
0 to 10kΩ(It takes approx. 1 Second
for Settings) |
| Others |
LOAD ON/OFF, EXT SW |
| Series/Parallel(Master/Slave
Operation) |
Connecting Capability |
Maximum 4 of Slave Units plus 1 Master Unit |
| Added Current Display |
Total Value of Slave Unit(s) and Master Unit
are Displayed at Master Unit Display. Over Write : 2 times/Sec |
| Resolution (L Range/H Range) |
0.1 x N / 10 x N (mA) N: Parallel Unit Numbers. |
| Current Monitor Out |
Linearity |
±1% FS |
| DC Current Measurement |
Range/ (Resolution) |
0.3 / 30 A / (0.1/10 mA) |
| Accuracy/Repeat |
±0.2% of rdg ±0.3% of FS (0
to 40°C) / 2 Times/Sec |
| DC Voltage Measurement |
Range/Resolution |
0 to 20V / 1mV, 20 to 210V / 10mV (Auto Range,
Hysteresis at 18 /20V) |
| Accuracy/Repeat/Temperature
Factor |
20V Range: ±0.03% of rdg ±0.06%
of FS, 200V Range: ±0.03% of rdg ±0.03% of FS (18
to 28°C) / 2 Times/Sec / ±0.003% of rdg ±0.003%
of FS/°C |
| Power Measurement |
Range/Resolution |
1.5, 150W / 1, 100mW (Voltage x Current) |
| UVP (Under Voltage) |
Range/Resolution |
OFF, -0.5 to 20 V/20mV |
| OPP (Over Power) |
Range/Resolution |
H Range: 15 to 165W/1W / L Range: 0.15 to
1.65W/10mW |
| OCP (Over Current) |
Setting Range/Resolution |
H Range: 3 to 33A/150mA / L Range: 0.03 to
0.33A/1.5mA |
| Protection |
Over Voltage |
Cut Load Off about 230V |
| Over Current, Over Power |
Automatic Resume After 3 Sec of Load Off |
| Reversed Connection |
Terminate by Parasitic FET |
| Over Heating |
Cut Load Off at 110°C at Inside Heat
Sink |
| Sequence Memory |
Step/Time/Resolution |
100 / 50μs to 99h59m59.99995s, PAUSE,
PASS / 50μs, Cycle: 1 to 255 |
| Items |
Discharge Mode Pre-set A, B and C Value,
Pre-set A, B and C Switch Selection, Discharge Mode, SHORT Mode
ON/OFF, LOAD ON/OFF, UVP Setting value, OCP Setting value, OPP Setting
Value, Soft Start Setting Value, Tr/Tf
Setting value, SW Frequency, SW DUTY, CV RANGE, Current RANGE, External
Control Mode (PASS at Auto Sequence Mode) |
| Environmental Request |
Temperature/Humidity |
0 to 40°C / 20 to 85 %RH |
| Power Source |
AC90 to 132V / AC180 to 250V, 48 to 63 Hz |
| Power Consumption |
Less than 75VA |
| Isolation |
Primary to Body: 1500VAC 1 Minute, Primary
to Secondary: 2300VAC 1 Minute |
| Isolation Resistance |
Primary to Body, Primary to Secondary: 500
VDC More Than 10MΩ, Secondary to Body: 250VDC More Than 5MΩ |
| Cooling Method |
Cooling Fan |
| Dimensions (Maximum) |
WxHxD: 210 (210) x 124 (141) x 405 (538)
(mm) |
| Weight |
Approx. 6 kg |
;)
