| The CS-5400 Series are 3-channel oscilloscopes
developed with concepts of high level design‚high accuracy and
easy operation. The panel layout never diminishes the intuitive
and high-speed response provide fatigue free operation even after
long-hours of use. These models incorporating readout function
(with CS-5400 / 5450) offer you parameter measurement and auto
setup functions enabling to measure AC voltage (Vp-p) ‚ DCvoltage‚frequency
and period. All of these models are provided with full features
including ±2% high-accuracy measurement‚delay sweep function‚automatic
triggering and high intensity‚high-resolution CRT. The CS-5400
Series with high-performance will surely assist you in many kinds
of field activities.
Parameter Auto Measurement Function
It is possible to measure the voltage, frequency and period automatically
just input the signal. Especially for voltage measurement, measurement
mode is automatically selected according to the input selector.
For example, when the AC input is selected, "Peak-to-Peak" voltage
is automatically measured, and when the DC input is selected,
DC voltage is measured automatically.
Auto Setup Function(CS-5400/5450)
By pressing the AUTO SET key, the voltage range and time range
are selected automatically.
Cursor Measurement Function(CS-5400/5450)
The cursor measurement function allows a high accuracy measurement
of signal values. When the probes are used, its attenuation ratio
can be converted automatically. It is also possible to measure
the voltage value and phase differences. When the delay sweep
is used, the delay time is also displayed, enabling an accurate
measurement results without any errors due to visual checks in
conventional systems.
Peak to Peak Voltage Measurement(CS-5400/5450)
Parameter automatic measurement function enables automatic AC
peak to peak voltage measurement up to 5MHz.
Variable Lock(CS-5400/5450)
ON/OFF the vertical and horizontal variable functions can be set
when pressing the ALT/CHOP knob more than 1-second. When OFF is
selected, it becomes CAL level. When the function is ON, it returns
to prior value.
3-Channel 8-Trace Waveform Display
CS-5400 series enable the display of CH3 input in addition to
CH1 and CH2. These three input signals to CH1, CH2 and CH3 can
be displayed at the same time as the main (A) sweep waveform.Furthermore,
an alternated delay sweep function displayed as the delayed (B)
sweep waveforms of each signal.
High-Sensitivity Design with Vertical Axis of 1 mV/div
The vertical axis sensitivity can be varied continuously from
1 mV/div. to 5 V/div. using the 1-2-5 step attenuator. The 1 mV/div.
position is very useful to measure low-level and complicated signals.
(Frequency response at 1 mV/div. and 2mV/div are DC to 20 MHz
(-3 dB)).
Automaticv Sync (FIX) Function
With this function, the synchronization level is automatically
controlled by tracking the amplitude of the waveform to maintain
the sync lock status. This function eliminates annoying and complicated
synchronization operations.
Easy Operation Panel Layout
The CS-5400 and CS-5450 used touch switches and LEDs. The CS-5405
and CS-5455 used push switches and lever switches for easy operation.
Delayed Sweep with Waveform Partial Magnification Capability
The main (A) sweep waveform in which the magnified section is
brightened by intensity modulation and the delayed (B) sweep waveform
which shows only the magnified section can be observed simultaneously.
This is a real alternate delayed sweep.
V Mode Sync for Stable Display of 3 Signals
Even when the CH1, CH2 and CH3 input signal frequencies are different,
each signal can be synchronized securely and its waveform can
be displayed stably.
High-Accuracy ± 2% Design for More Precision Measurement
In order to obtain highly reliable measurement results, the vertical
axis sensitivity and sweep time for the main circuit is maintained
within ± 2% precision. Other specifications also guarantees the
rated values (under temperature conditions of 10 to 35?C, humidity
of 85% or less).
Maximum Sweep Rate of 5 ns/div (x10 MAG)
The sweep rate can be varied continually from 0.5 s/div to 50
ns/div. The signal delay line is installed so that the positive
rise of high-speed signals and high-frequency signals can be measured
accurately
Built in Video Clamp Circuit for Easy Operation
Built in Video Clamp function which enables observation of the
flame and line TV signals at the touch of a button, while high-stability
synchronization is obtained without performing annoying synchronizing
operations.
Square-Type 150 mm CRT with Self-Illuminated Light and Inside
Scale (12 kV)
A large-sized, square, dome-mesh type CRT with accelerator is
employed. It features both high intensity and high resolution
while providing accurate measurements without parallax view. The
auto focus circuit is also incorporated to display sharp waveforms
at all times.
Single Sweep for Observations of Single-shot Channel
The single sweep function is powerful in measurement of single-shot
or sudden channel. Waveform photography using a camera is as easy
as ordinary, visual observations. It is easy not only for observations
during normal visual inspections but also for camera shots of
the waveforms.
Variable Hold-off Allowing Observation of Waveforms with Complicated
Cycle
Signals which are hard to be synchronized due to complicated repetition
cycles, for example digital signals and video bursts signal, can
be synchronized stably by converting them into the hold-off time.
High-Accuracy Calibration Signals
A calibration signal output is provided to output the highly accurate
frequency of ± 0.1% and voltage accuracy of ± 1%, enabling checking
of the measurement precision at any required time.
CH1 Signal Output Connector
The CH1 signal output is obtained by branching the input signal
in the middle of the signal line. As this connector outputs the
input signal at a rate of 50 mV/div, connecting a frequency counter
makes it possible to measure the frequency of a very low signal
while observing its waveform
Wide Dynamic Range and Distortion-Free Accurate Waveform Display
Its wide dynamic range having greater margins assures the linearity
of the waveforms displayed on the CRT, providing highly accurate
waveform displays without any distortion up to the upper frequency
limits.
Other Features
All position knobs and controls are provided on the front panel.
A High-sensitivity X-Y function is convenient for the measurement
of phase differences between two input signals.
A Trace Rotation function allows an easy correction of the inclination
of the trace line due to earth magnetism.
LINE Synchronization is provided
A Trace Separation function shifts the B sweep waveform upward
or downward by 4 div. from A sweep waveform.
The waveform to which the brightness modulation is applied can
also be observed.
Added or extracted waveforms using ADD and CH2 INV functions can
also be observed.
Scale illumination convenient for taking photographs or observation
in dark areas is provided.
CRT scale also provides 0, 10, 90 and 100% indications; convenient
for measurement of rising time, etc.
A 10-times sweep waveform magnification function (X10 MAG) is
provided.
|
;)
