SPECIFICATIONS
CRT	Type	GRS-6052: 6-inch CRT 150CTB31, 10kV GRS-6032: 6-inch CRT D14-363GY, 2kV
	INTEN and FOCUS	Front panel control
	Illumination	Front panel control
	Z-axis Output	Sensitivity: at least 5V (TTL)
		Polarity: positive going input decrease intensity
		Max.input voltage: 30V (DC+AC peak)
		GRS-6052: Input impedance: approx. 47kΩ GRS-6032: Input impedance: approx. 33kΩ
VERTICAL SYSTEM	Sensitivity and Accuracy	1mV ~ 2mV/DIV±5%, 5mV ~ 20V/DIV±3%, 14 calibrated steps in 1-2-5 sequence
	Variable Continuously	2.5:1 ~ min. 50V/DIV
	Bandwidth (-3dB) and Rise Time	Bandwidth(-3dB) Rise Time GRS-6052 5mV ~ 20V/DIV DC ~ 50MHz Approx. 7nS 1mV ~ 2mV/DIV DC ~ 7MHz Approx. 50nS GRS-6032 5mV ~ 20V/DIV DC ~ 30MHz Approx. 11.7nS 1mV ~ 2mV/DIV DC ~ 7MHz Approx. 50nS
	Vertical Mode	CH1, CH2, DUAL(ALT or CHOP)
	Chopper Frequency	Approx. 250kHz
	Sum or Difference	CH1+CH2, CH1-CH2
	Invert	CH2
	Input Impedance	Approx. 1MΩ±2% // approx. 25pF
	Input Coupling	AC, DC, GND
	Maximum Input Voltage	400V (DC + AC peak)
HORIZONTAL SYSTEM	Sweep Time	0.2µS/DIV ~ 0.5S/DIV, 20 steps selectable in 1-2-5 sequence
	Variable Continuously	2.5:1 UP TO 1.25s/DIV (uncal.)
	Accuracy	±3%, ±5% at x5, x10 MAG. ±8% at x20 MAG
	Sweep Magnification	x5, x10, x20
	Max. Sweep Time	GRS-6052: 20nS/DIV (10nS/DIV are uncalibrated)
		GRS-6032: 50nS/DIV (10nS/DIV ~ 40nS/DIV are uncalibrated)
	ALT-MAG Function	YES
	HOLD-OFF Time	Variable
TRIGGER SYSTEM	Trigger Modes	AUTO, NORM, TV
	Trigger Source	VERT, CH1, CH2, LINE, EXT
	Trigger Coupling	AC, HFR, LFR, TV-V(-), TV-H(-)
	Trigger Slope	"+" or   "-" polarity
	ALT Trigger	YES
	Trigger Sensitivity	GRS-6052 CH1,2 VERT -MODE EXT 20Hz ~ 5MHz 0.5 DIV 2.0 DIV 200mV 5MHz ~ 40MHz 1.5 DIV 3.0 DIV 800mV 40MHz ~ 50MHz 2.0 DIV 3.5 DIV 1V
		GRS-6032 CH1,2 VERT -MODE EXT 20Hz ~ 5MHz 0.5 DIV 2.0 DIV 200mV 5MHz ~ 40MHz 1.5 DIV 3.0 DIV 800mV
		TV sync pulse more than 1 DIV (CH1, CH2, VERT-MODE) or 200mV(EXT)
	External Trigger Input	Input Impedance: Approx. 1MΩ // 25pF (AC coupling)
		Max. input voltage: 400V (DC+AC peak) at 1kHz
X-Y OPERATION	Input	X-axis:CH1 ; Y-axis:CH2
	Sensitivity	1mV/DIV ~ 20V/DIV
	Bandwidth	X-axis: DC ~ 500kHz (-3dB)
	Phase Difference	3º or less from DC to 50kHz
DIGITAL STORAGE	Acquisition Memory	8 bit ADC x 2
	Maximum Sampling rate	500MS/s for Equivalent time sampling 100MS/s for normal sampling
	Storage Bandwidth	Single shot:DC~5MHz(-3dB) Repetivivevent: GRS-6052: DC~50MHz ±5DIV GRS-6032: DC~30MHz ±5DIV
	Dynamic Range	±5DIV
	Memory Length	Acquisition Memory: 2kW/CH*2, 1kW/CH(equivalent) Save REF Memory: 1kW/CH*10 with back-up memory Display memory: 1kW/CH*4 waveform (max.)
	Sweep Time	Equivalent: 0.2µs/DIV~0.5µs/DIV Normal: 1µs/DIV~0.1s/DIV ROLL: 0.2s/DIV~100s/DIV
	Sweep Magnification	x5, x10, x20
	Max. Sweep Time	10ns/DIV
	MAG Interpolation	DOT, Linear
	ALT-MAG Function	YES
	Acquire Mode	Sample, Peak Detect(>25ns), Envelop, Per-sist, Average(2~256)
	Operation Mode	Auto, Norm, Single, Single-Roll, Roll, X-Y, Average(2~256), Run/Stop
	Smoothing Function	Dot joint ON/OFF selectable
	Pre-Trigger	0~10DIV in 0.02DIV steps
	X-Y Operation	X-axis: CH1, Y-axis: CH2 Storage Bandwidth: GOS-6052: DC~50MHz(-3dB) GOS-6032: DC~30MHz(-3dB)
	Display Resolution	H:100points/DIV ; V:25 points/DIV X-Y: 25*25 points/DIV
Waveform SAVE/RECALL	10 sets (REF0~REF9)
CURSOR READOUT	Cursor Measurement	ΔV, ΔT, 1/ΔT
	Readout Intensity	Adjustable
OUTPUT SIGNAL
	CH1 Signal Output	Voltage: approx. 20mV/DIV (with 50Ω terminated); Bandwidth: 50Hz~5MHz
	Calibrator Output	Voltage: 0.5V ±3% Frequency: approx. 1kHz,  Square wave
INTERFACE		RS-232C Interface
POWER SOURCE		AC 100V/120V/ 230V + 10%, 50/60Hz
ACCESSORIES		Power cord x 1, Instruction manual x 1, Probes(10:1/1:1) x 2
DIMENSIONS & WEIGHT		275(W) x 130(H) x 370(D) mm, Approx. 7.2kg