Technical Data
Input Characteristics	Input impedance: 1 MW, 20 pF Voltage Rating: 600V rms, CAT III
Volt/Amps/Hertz Display	True-rms voltage (ac+dc) Ranges: 5.000V, 50.00V, 500.0V, 1250V* Accuracy: ±(1% +10 counts) True-rms current (ac + dc) Ranges: 50.00A, 500.0A, 5.000 kA, 50.00 kA Accuracy: ±(1% +10 counts) Mains frequency Ranges: 40.0 to 70.0 Hz Accuracy: ±(0.5% +2 counts)
Power Display	Watts, VA, VAR Ranges: 250 W, 2.50 kW, 25.0 kW, 250 kW, 2.50 MW, 250 MW Accuracy: ±(4% + 4 counts) Power Factor, PF Displacement Power Factor, DPF Range: 0.00 to 0.25 Accuracy: Not specified Range: 0.25 to 1.0 Accuracy: ±0.04
Harmonics Display	Voltage Ranges: 1st to 51st harmonic Accuracy: ±(3% +2 counts) to ±(15% +5 counts) Current Ranges: 1st to 51st harmonic Accuracy: ±(3% +8 counts) to ±(5% +8 counts) Power Ranges: 1st to 51st harmonic Accuracy: ±(5% +2 counts) to ±(30% +5 counts) Line frequency Ranges: 40 Hz to 70 Hz fundamental Accuracy: ±0.25 Hz Phase Ranges: 2nd to 51st harmonic Accuracy: ±3 º to ±15 º K-factor Ranges: 1.0 to 30.0 Accuracy: ±10%
Sags and Swells Recording	Recording times: 4 min to 16 days (selectable) True-rms voltage: Ranges: 5.000V, 50.00V, 500.0V, 1250V* Accuracy: ±(2% +10 counts) True-rms current Ranges: 50.00A, 500.0A, 5.000 kA, 50.00 kA Accuracy: ±(2% +10 counts)
Other Recording	Recording times: 4 min to 16 days (selectable) Parameters: Choose up to two from one of the groups below V/A/Hz: Line voltage, current, frequency Power: Watts, VA, VAR, PF, DPF, frequency Harmonics: THD, harmonic voltage, (or current, or power), frequency, % of total, phase Ohms: Ohms, diode, continuity, capacitance Temperature: Temperature Scope: DC voltage, dc current, ac voltage, ac current, frequency, pulse width, phase, duty cycle, peak max, peak min, peak min-max, crest factor
Transient Capture	Minimum pulse width: 40 ns Voltage threshold settings: 20%, 50%, 100%, 200% above or below normal voltage Min voltage and max voltage at cursor: Ranges: 10V, 25V, 50V, 125V, 250V, 500V, 1250V Accuracy: ±5% of full scale
Inrush Capture	Current ranges: Ranges: 1A, 5A, 10A, 50A, 100A, 500A, 1000A Inrush times: Ranges: 1s, 5s, 10s, 50s, 100s, 5 min Cursor readings, Current at cursor Ranges: 12.5A, 25A, 50A, 125A, 250A, 500A, 1250A, 2500A, 5 kA Accuracy: ±5% of full scale Time between cursors Ranges: 4 to 235 pixels (1 pixel = inrush time/250) Accuracy: ±(0.2% + 2 pixels)
Scope Display	Time ranges: Ranges: 20 ns/div to 60 s/div Max sampling rate: Ranges: 25 MS/s Bandwidth: Voltage channel [1]: 20 MHz at inputs, 1 MHz with TL24 Leads Current channel [2]: 15 kHz at inputs, 10 kHz with 80i-500s Probe Coupling: AC, DC Vertical sensitivity: Ranges: 5 mV/div to 500V/div Vertical resolution: 8 bit (256 levels) Record length: 512 samples per channel Timebase modes: Normal, roll, single Pre-trigger: Up to 10 divisions Measurements: dc, ac, ac+dc, peak, peak-peak, frequency, duty cycle, phase, pulse width, crest factor
Ohms, Diode,Continuity	Ohms: Ranges: 500.0W, 5.000 kW, 50.00 kW, 500.0 kW, 5.000 MW, 30.00 MW Accuracy: ±(0.6% +5 counts) Diode voltage: Accuracy: ±(2% +5 counts) Continuity: Beeper on at < (30W ±¤5W) Max current: 0.5 mA Capacitance: Ranges: 50.00 nF, 500.0 nF, 5.000 µF, 50.00 µF, 500.0 µF Accuracy: ±(2% +10 counts) Temperature** Ranges: -100.0 ºC to 400.0 ºC, -200.0 ºF to 800.0 ºF Accuracy: ±(0.5% +5 counts)
Screen Memories	10
Optically Isolated RS-232 Interface	To printer: Supports HP Laserjet®, Deskjet®, Epson FX/LQ and Postscript printers with optional PAC91 Printer Adapter Cable To PC: FlukeView® Power Quality Analyzer Software included
FlukeView Power Quality Software	Hardware requirements: PC or 100% compatible with Windows® 3.1, Windows® 95, or Windows NT® . Enough RAM for Windows operating system. 4 MB hard drive space. Pointing device (mouse) recommended.

^*Rated 600V CAT III
^**Requires optional temperature accessory

General Specifications
Power	Line voltage adapter/battery charger included Installed battery: Rechargeable Ni-Cd pack Operating time: 4 hours Charging time: 4 hours
Environmental	Temperature: 0ºC to 50ºC (32ºF to 122ºF) Environmental: MIL 28800E, Type 3, Class III, Style B Enclosure: IP51 (dust, drip water proof)
Mechanical Data	Size: (H x W x D) 232 x 115 x 50 mm (9.1 x 4.5 x 2 inches) Weight: 1.1 kg (2.5 lbs)
Safety	For measurements on 600V rms Category III installations, Pollution Degree 2, per: ANSI/ISA S82.01-1994 EN61010-1 (1993) (IEC1010-1)CAN/CSA-C22.2 No. 1010.1-92 UL3111-1 (approval pending) Surge protection: 6 kV on input A and B Floating measurements: 600V rms from any terminal to ground Warranty: 3 years parts and labor on Fluke 43, 1 year on accessories