| VERTICAL AMPLIFIERS (CH 1 and CH 2) |
| Sensitivity |
5mV/div to 5V/div. 1 mV/div to 1V/div (at X5 MAG) |
| Attenuator |
10 calibrated steps in 1-2-5 sequence.
Vernier control provides fully adjustable sensitivity between steps, adjustment range 1/1 to 1/2.5 |
| Accuracy |
+-3% (+-5% at X5 MAG) |
| Input Impedance |
1M + 3% |
| Input Capacitance |
25 pF +- 10pF |
| Frequency Response |
DC: DC to 100 MHz (-3 dB) |
| X5 MAG |
DC to 20 MHz (-3 dB) |
| AC |
10Hz to 100 MHz (-3 dB) |
| Rise Time |
3.5 ns (Overshoot <=5%) |
| Signal Delay Time |
Variable |
| Square Wave Characteristics |
Overshoot less than 5%, 10mV/div range
Other ranges within 5% additional |
| Maximum Input Voltage |
400V (DC + AC peak) |
| VERTICAL AMPLIFIERS |
| Operating Modes |
CH 1, CH 2, Dual, Add |
| Delay Time Between Channels |
Within 1 ns between CH 1 and CH 2 |
| Crosstalk |
30:1 at 100 kHz |
|
|
| SWEEP SYSTEM |
| A |
A sweep |
| B |
Delayed B sweep |
| B TRIGGERED |
B sweep triggered after delay |
| A Time Base |
| Sweep Mode |
Auto, normal |
| Sweep Time |
5s to 20ns/div., 23 steps in 1-2-5 sequence with variable control |
| Accuracy |
+-3% |
| Hold Off Time |
Continuously variable. Adjustment range from normal to 1,5 times the sweep time |
| B Time Base |
| Delay Method |
Continuous delay. Triggered delay |
| Sweep Time |
20ns to 0.5s/div., 23 steps in 1-2-5 sequence |
| Accuracy |
+-3% |
| Hold Off Time |
Continuously variable. Adjustment range from normal to 1.5 times the sweep time |
| B Time Base |
| Delay Method |
Continuous delay. Triggered delay |
| Sweep Time |
20 ns. to 0.5s/div., 23 steps in 1-2-5 sequence |
| Accuracy |
+-3% |
| Delay Time |
Start point: 0.5 div to + 0.3 div |
| End point |
10 div + 1 div |
| Delay Jitter |
Within 1/10,000 of full scale sweep time |
| TRIGGERING |
| A Trigger |
| Source |
CH 1, CH 2, LINE, EXT |
| Sensitivity |
30Hz to 110 MHz |
| TV-V |
20Hz - 30kHz |
| TV-H |
3 kHz - 100 kHz |
| Slope |
+ or - |
| B Trigger |
The A trigger is also the B trigger |
| EXTERNAL TRIGGER |
| Input Impedance |
1 m, 30 pF |
| Maximum Input Voltage |
300V (DC + AC peak) |
| HORIZONTAL AMPLIFIER |
| X-Y Mode |
X Axis = CH 1, Y Axis = CH 2 |
| Sensitivity |
5 mV/div to 5 V/div, CH 1 and CH 2 |
| Accuracy |
+- 3% calibrated position, +-6% using x10 MAG |
| Frequency Response |
DC: DC to 100 MHz (-3 dB) |
| X5 MAG |
DC to 20 MHz (-3 dB) |
| AC |
10 Hz to 100 MHz (-3 dB) |
| Rise Time |
3.5 ns (Overshoot <=5%) |
| Signal Delay Time |
Variable |
| Square Wave Characteristics |
Overshoot less than 5%, 10 mV/div range
Other ranges within 5% additional |
| Maximum Input Voltage |
400V (DC + AC peak) |
| VERTICAL AMPLIFIERS |
| Operating Modes |
CH 1, CH 2, Dual, Add |
| Delay Time Between Channels |
Within 1 ns between CH 1 and CH 2
Crosstalk 30:1 at 100 kHz |
| SWEEP SYSTEM |
| Operating Modes |
| A |
A sweep |
| B |
Delayed B sweep |
| B TRIGGERED |
B sweep triggered after delay |
| A Time Base |
| Sweep Mode |
Auto, normal |
| Sweep Time |
5s to 20ns/div., 23 steps in 1-2-5 sequence with variable control |
| Accuracy |
+-3% |
| Hold Off Time |
Continuously variable. Adjustment range from normal to 1.5 times the sweep time |
| B Time Base |
| Delay Method |
Continuous delay. Triggered delay |
| Sweep Time |
20ns. to 0.5s/div., 23 steps in 1-2-5 sequence |
| Accuracy |
+-3% |
| Delay Time |
Start point: 0.5 div to + 0.3 div |
| End point |
10 div + 1 div |
| EXTERNAL TRIGGER |
| Input Impedance |
1 m, 30 pF |
| Maximum Input Voltage |
300V (DC + AC peak) |
| HORIZONTAL AMPLIFIER |
| X-Y Mode |
X Axis = CH 1, Y Axis = CH 2 |
| Sensitivity |
5 mV/div to 5 V/div, CH 1 and CH 2 |
| Accuracy |
+-3% calibrated position, +-6% using x10 MAG |
| Frequency Response |
DC to 2 MHz (-3 dB) |
| CH I (Y) OUTPUT |
| Output Voltage |
Approx. 100mV/div open circuit
Approx. 50 mV/div into 50 |
| Freq. Response |
50 Hz to 30 MHz |
| Output Impedance |
approx. 50 |
| CRT |
| Type |
Rectangular with integral graticule |
| Display Area |
8x10 div (1 div = 1 cm) |
| Accelerating Voltage |
15 kV |
| Phosphor |
P31 |
| Scale Illumination |
None |
| Trace Rotation |
Electrical, front panel adjustable |
| Other Specifications |
| Z Axis (Intensity Modulation) |
Sensitivity: 3V or greater, TTL level.
Negative polarity increases brightness |
| Input Impedance |
15 k |
| Usable Freq. Range |
DC to 3.5 MHz |
| Maximum Input Voltage |
20 V (DC + AC peak) |
| CAL/Probe Compensation |
| Waveform |
Positive going squareware |
| Output Voltage |
0.5 V p-p +- 3% |
| Frequency |
Approx. 1 kHz |
| Duty Cycle |
50 +- 5% |
| Power Requirements |
100/120/220/240/VAC +- 10%, 50/60 Hz, approximately 55 W |
| Dimensions (HxWxD) |
12.76x15.68x5.2" (324x398x132 mm) |
| Weight |
18.7 lbs. (8.5 kg) |
| ENVIRONMENT |
| Within Specified Accuracy |
50 0 to 95 0 F (10 0 to 35 0 C), 85% maximum RH |
| Full Operation |
32 0 to 104 0 F (0 0 to +40 0C), 85% maximum RH |
| Storage |
-4 0 to 158 0 F (-20 0 to +70 0 C) |
;)
