| VERTICAL AMPLIFIERS (CH 1 and 2) |
| Sensitivity |
5mV/div to 1V/div x 5mag |
| Attenuator |
1-2-5 sequence, plus x 5 gain step. Vernier control provide fully adjustable sensitivity between steps range 1/1 to at least 1/2.5 |
| Accuracy |
+-3%, 5mV to 5V/div; +-5%, 1 mV, 2mV/div |
| Input Impedance |
1M +-2% |
| Input Capacitance |
25 pF +-10% |
| Frequency Response |
DC to 60 MHz |
| Rise Time |
5.8ns (Overshoot <= 5%) |
| Operating Modes |
CH1, CH2, Dual, Alternate Chop |
| Polarity Reversal |
CH 2 invert |
| Maximum Input Voltage |
400V (DC + AC Peak), 800 VAC p-p |
| SWEEP SYSTEM |
| Sweep Display Modes |
Main, Mix, Delay |
| Hold Off Time |
5:1 continuously variable |
| Main Sweep |
| Sweep Speed |
0.1us/div. to 2.0s/div. in 1-2-5 sequence, 23 steps |
| Accuracy |
+-3% |
| Variable Time Control |
5:1, uncalibrated, continuously variable between steps |
| Sweep Magnification |
10 x, +-10%, extended sweep speed up to 10ns/div |
| Delay Sweep |
| Sweep Speed |
0.1us/div. to 2.0s/div. in 1-2-5 sequence, 23 steps |
| Accuracy |
+-3% |
| Sweep Magnification |
10 x, +-10%, extended sweep speed up to 10ns/div |
| Delay Time Position |
Variable control to locate desirable waveform for extending |
| Triggering |
| Trigger Coupling |
AUTO, NORM, TV-V, TV-H |
| Trigger Source |
CH1, CH2, ALT, EXT, LINE |
| Slope |
+/- |
| HORIZONTAL AMPLIFIER (Input through channel 2 input) |
| X-Y Mode |
CH 1: Y axis. CH 2: X axis |
| Sensitivity |
Same as vertical channel 2 |
| Accuracy |
+-3%, Y axis: +-5% X axis |
| Input Impedance |
Same as vertical channel 2 |
| Frequency Response |
DC: DC to 1 MHz (-3 dB). AC: 5 Hz to 2 MHz (-3 dB) |
| X-Y Phase Difference |
3 0 at 50 kHz |
| Maximum Input Voltage |
Same as vertical channel 2 |
| CH 2 Output (on rear panel) |
| Output Voltage |
50 mV/div (nominal into 50 load) |
| Output Impedance |
Approximately 50 |
| Frequency Response |
20Hz to 60MHz, -3dB into 50V |
| CRT |
| Type |
6-inch rectangular with internal graticule |
| Display Area |
8x10div (1 div = 1 cm) |
| Accelerating Voltage |
12k |
| Phospor |
P31 |
| Scale Illumination |
Continuously variable |
| Trace Rotation |
Electrical, front panel adjustable |
| COMPONENT TESTER |
| Components Tested |
Resistors, capacitors, inductors, and semiconductors |
| Test Voltage |
6V rms maximum (open) |
| Test Current |
11 mA maximum (shorted) |
| Test Frequency |
Line frequency (60 Hz in USA) |
| Other Specifications |
| Cal/Probe Compensation Voltage |
2.0V p-p +-2% square wave, 1 kHz nominal |
| Sweep Output |
TTL level allows synchronization of external equipment with scope sweep |
| Intensity Modulation |
| Input Signal |
TTL level, intensity increasing with more negative levels |
| Input Impedance |
Approx. 1k |
| Usable Freq. Range |
DC to 5MHz |
| Maximum Input Voltage |
5V (DC + AC peak) |
| Environment |
| Within Specified Accuracy |
50 0 to 95 0 F (10 0 to 35 0 C), 85% maximum RH |
| Full Operation |
32 0 to 122 0 F (0 0 to +50 0 C), 10 - 80% RH |
| Storage |
-22 0 to 158 0 F (-30 0 to +70 0 C), 10-90% RH |
| Power Requirements |
110/120/220/240 V +- 10%, 50/60 Hz |
| Dimensions (HxWxD) |
12.76 x 15.68x5.2\'\' (324x398x132 mm) |
| Weight |
16.75 lbs. (7.6 kg) |
;)
